LEZSDSSMB1C1

ZS-DSSM-B1C1-CH

Lectrosonics

The Lectrosonics DSSM Water-Resistant Micro Digital Wireless Transmitter (537 to 662 MHz) with Charger includes a DSSM transmitter and a CHSDSSM 4-bay, drop-in charging station. To operate, the charger requires the DCR5/9AU AC/DC power supply (available separately).Built for the Most Demanding Work Environments The IP57 rating indicates that the unit is protected against dust ingress while also withstanding water immersion up to 3.2' for 30+ minutes all while allowing for quick battery swap-outs The housing is constructed of machined aluminum alloy treated in the conductive, super hard electroless nickel ebENi finish The audio-input jack is a 3-pin LEMO connector with a threaded collar adding additional ruggedness Dock-Charging Capability The optional CHSDSSM battery charging station provides a convenient and organized way of recharging any mix of four DSSM transmitters and/or four LB-50 lithium-ion batteries Full charging of battery takes 3 hours The DSSM transmitter can operate up to 6 hours on a full charge For larger systems with numerous batteries in regular use, the CHSDSSM charger may be daisy-chained to 3 additional CHSDSSM chargers using a single DCR5/9AU AC/DC power supply (available separately) for a total of 16 LB50s and/or DSSMs charging at once Versatile Input Section with Limiter The input section features the unique Lectrosonics servo bias input circuitry accepts mic- or line-level signals with a wide range of gain adjustment in 1 dB steps Accurate indications on the display allow precise gain adjustments to be made for the maximum signal to noise ratio and minimum distortionA DSP-controlled analog audio limiter is employed ahead of the first mic preamp to protect the entire audio chain from overload. The limiter has a range of more than 30 dB for excellent overload protection, and a dual-release envelope that makes the limiter acoustically transparent while maintaining low distortion of brief transients and longer duration peaks Selectable low-frequency roll-off at 35, 50, 70, 100, 120, and 150 HzClear and Simple Controls The membrane switch panel and OLED display enable access to all adjustments and settings. The menu structure is easy to navigate Battery status is indicated by a bi-color LED that is green with a fresh battery, then turns to red as the battery runs down, and finally starts blinking red when there are only a few minutes of runtime remaining AES 256-bit CTR Encryption The DSSM offers AES 256-bit CTR encryption with four key policies including Universal, Shared, Standard, and Volatile. This covers a wide variety of use cases, including government, corporate, and sports coverage Remote Control via LectroRM App LectroRM (available separately) is a third-party mobile application for iOS and Android smartphone operating systems. Its purpose is to make changes to the settings on the DSSM transmitter by delivering encoded audio tones to the microphone attached to the transmitter When the tone enters the transmitter, it is decoded to make a change toa variety of different settings such as input gain, frequency, and more Key Features Compatible with DSQD, DCHR, M2Ra, DSR, DSR4, and DCR822 receiversAudio-input connector: LEMO 3-pinIP57 rating: avoids water ingress for 30 minutes or more when submerged under 3.3' of waterRemovable battery: the DSSM uses an LB-50 rechargeable lithium-ion batteryEasy-to-use onboard buttons and rich display, with the same menu structure as the company's DBSM family of transmittersUSB jack located inside the battery compartment for firmware updates in the field, using Wireless Designer softwareAll-metal constructionRemovable antenna with SMA mountRF Power settings at 10, 25, and 50mW in D2 mode and 4mW for HDM modeAES 256-bit CTR encryption with four key policies including universal, shared, standard, and volatile (this covers a wide variety of use cases, including government, corporate, and sports cov